1、原理：超聲波清洗設備是利用超聲波的高頻振動產生能量，這種能量可以在清洗液中產生微小氣泡，并在物體表面爆炸，從而去除物體表面的垢和雜質。具體來說，超聲波清洗機由以下幾個分組成：超聲波發生器：超聲波發生器是產生超聲波的核心件，它通過電子振蕩電路產生高頻電信號，然后將其轉換為機械振動，產生超聲波。換能器：換能器是將電信號轉換為機械振動的重要件，它通常由壓電陶瓷等材料制成。換能器將超聲波發生器產生的電信號轉換為機械振動，并將這種振動放大，從而產生超聲波。清洗槽：清洗槽是放置被清洗物品的地方，同時也是容納清洗液的地方。清洗槽通常由不銹鋼材料制成，能夠承受一定的壓力和溫度。控制面板：控制面板是超聲波清洗機的控制中心，可以設置清洗時間、功率等參數。

1. Principle: Ultrasonic cleaning equipment uses the high-frequency vibration of ultrasonic waves to generate energy, which can create tiny bubbles in the cleaning solution and explode on the surface of the object, thereby removing dirt and impurities from the surface of the object. Specifically, the ultrasonic cleaning machine consists of the following components: ultrasonic generator: The ultrasonic generator is the core component that generates ultrasonic waves. It generates high-frequency electrical signals through an electronic oscillation circuit, which are then converted into mechanical vibrations to produce ultrasonic waves. Transducers: Transducers are important components that convert electrical signals into mechanical vibrations, typically made of materials such as piezoelectric ceramics. The transducer converts the electrical signal generated by the ultrasonic generator into mechanical vibration and amplifies this vibration to produce ultrasonic waves. Cleaning tank: The cleaning tank is a place to place the items to be cleaned and also a place to hold the cleaning solution. The cleaning tank is usually made of stainless steel material and can withstand certain pressure and temperature. Control panel: The control panel is the control center of the ultrasonic cleaning machine, which can set parameters such as cleaning time and power.

2、使用方法

2. Usage method

準備：檢查清洗機是否正常連接電源，確保正常通電。將要清洗的物品放入清洗槽中，加入適量的清洗液。

Preparation: Check if the cleaning machine is properly connected to the power supply and ensure that it is powered on normally. Put the items to be cleaned into the cleaning tank and add an appropriate amount of cleaning solution.

啟動：按下啟動按鈕，超聲波清洗機會自動進行清洗。控制面板可以設置清洗時間、功率等參數。

Start: Press the start button, and the ultrasonic cleaning machine will automatically clean. The control panel can set parameters such as cleaning time and power.

觀察：觀察清洗過程，注意清洗物品的變化。如果發現有異常情況，應立即停止清洗。

Observation: Observe the cleaning process and pay attention to changes in the cleaning items. If any abnormal situation is found, the cleaning should be stopped immediately.

取出：當清洗時間到達設定值時，機器會自動停止清洗。

Extraction: When the cleaning time reaches the set value, the machine will automatically stop cleaning.

此時可以取出清洗物品，用清水沖洗干凈。結束：關閉控制面板上的電源開關，拔掉電源頭，清理現場。

At this point, you can remove the cleaning items and rinse them thoroughly with clean water. End: Turn off the power switch on the control panel, unplug the power plug, and clean up the site.

3、超聲波清洗機，是一種利用超聲波振動原理進行清洗的設備。其利用超聲波的振動作用將附著在物體表面的垢、油脂、雜質等分離和去除，具有清洗效果好、清洗速度快、清洗效率高、無需人工刷洗等優點。

3. Ultrasonic cleaning machine is a device that uses the principle of ultrasonic vibration for cleaning. It uses the vibration effect of ultrasound to separate and remove dirt, grease, impurities, etc. attached to the surface of objects, and has the advantages of good cleaning effect, fast cleaning speed, high cleaning efficiency, and no need for manual brushing.

本文由超聲波清洗機友情奉獻.更多有關的知識請點擊:http://m.czxhwj.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from the fully automatic ultrasonic cleaning machine For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message